Rods
Oval Wardrobe Tube
The main wardrobe hanging rail — oval aluminium tube in an 8-foot length, cut to size on site. The oval profile fits standard hangers snugly without the twist a round rod allows, so shoulders stay aligned and the run of clothes reads straight along the rail.
- Oval profile — 30 × 15 mm (1 3/16″ × 5/8″) — hangers don’t spin
- 2,500 mm / 8 ft 2″ length — cut to fit any bay
- Aluminium — lighter than steel, no rust in a damp closet
- 1.0 mm wall thickness (thicker 1.5 mm option available)
- Rod only — end supports and centre brackets specified separately
- Fits standard 32 mm system holes with dowel-based supports
Best specified in continuous runs across a bay of full-height hanging so the wardrobe reads as one line, not a broken sequence of rails.
Round Wardrobe Tube
A round wardrobe rail — aluminium, 33 mm diameter, 92 inches long, cut to size on site. Round rod stays universal — every standard hanger fits, and lifting a heavy coat off doesn’t jam it against the wall the way an oval profile can.
- Round profile — 33 mm / 1 5/16″ diameter
- 92″ / 2,337 mm length — cut to fit any bay
- Aluminium — no rust, lighter than steel
- Finishes: polished chrome, matt aluminium, matt nickel, matt gold, dark oil-rubbed bronze, slate
- Rod only — end and centre supports specified separately from the same range
- Supplied in packs of 12 rods
Best specified in wardrobe bays that mix garment types — the round profile lets hangers rotate freely, which matters when a heavy overcoat lifts a lighter shirt aside.
Valet
A pull-out rod that projects from the closet side panel — for hanging tomorrow’s outfit, drying a wet coat, or holding a garment bag flat while it fills. Retracts flush against the cabinet when you’re done.
- Extension arm — 11 3/4″ / 298 mm retracted, projects 7 9/16″ / 192 mm out from the cabinet
- 13.6 kg / 30 lb load — enough for a full outfit with a jacket
- Anodised aluminium, 24 × 24 mm profile
- Side-panel mount, retracts flush
- Five finishes: matt aluminium, matt nickel, matt gold, polished chrome, oil-rubbed bronze, slate
Best specified in the closet bay near the door — one valet rod turns morning dressing into a one-motion lift rather than a shuffle through the main hanging.
Closet Rod
A closet rod supplied at working length — pre-cut with end supports fitted, ready to install between two side panels. Oval aluminium profile so hangers stay square; six finishes to match handles and hooks in the same range.
- Oval profile — 19 × 32 mm / 3/4″ × 1 1/4″ — hangers don’t spin
- Five standard lengths: 17 3/4″, 23 3/4″, 29 3/4″, 35 3/4″, 47 15/16″ (or 92″ cut-to-fit)
- Anodised aluminium with a matching plastic end cap
- Six finishes: matt aluminium, matt nickel, matt gold, polished chrome (clear caps); dark oil-rubbed bronze, slate (black caps)
- Zinc-plated end supports included on the pre-cut lengths
,Side-panel mount
Best specified in single-bay sections where the whole rail is one span — no centre support means an uninterrupted line of clothes.
Welded Steel Oval Wardrobe Tube
The heavy-duty version of the wardrobe hanging rail — welded steel, chrome-plated, oval profile so hangers hold their line. For deep hanging bays or long spans where coats, suits and outerwear collectively weigh more than an aluminium tube should carry.
- Oval profile — 30 × 15 mm (1 3/16″ × 9/16″) — hangers don’t spin
2,337 mm / 92″ length — cut to fit any bay - Welded steel, chrome-plated — takes heavier loads than aluminium
- 1.0 mm wall thickness
- Rod only — end supports and centre brackets specified separately
- Supplied in packs of 10 rods
Best specified where the hanging is dense — a full coat collection, wool suits, weekend jackets — and the run needs a rod that won’t flex over time.
Hanger Attach Bar
A fixed horizontal bar with a nuthatch-shaped undulating profile — each trouser hanger clips at a slightly different height, so hangers overlap along the run rather than crowding side by side. More trousers fit the same rail width without one leg touching the next.
- Overlapping-hanger layout — trousers stack closer without touching
- Three cabinet widths: 600 mm / 23 5/8″, 800 mm / 31 1/2″, 900 mm / 35 3/8″
- Bar: 560 / 760 / 860 mm, 72 × 62 mm profile (2 13/16″ × 2 7/16″)
- Orange leather with pilgrim-grey frame — matches the pull-out and fixed trays
- Works with the Trouser Hanger — bought individually or in sets
Best specified with a set of trouser hangers — bar and hangers together turn one wardrobe bay into a season’s worth of trousers on display.